Omnitron iConverter Copper to fibre Media Converters

Omnitron iConverter managed copper to fibre media converters provide seamless integration of copper and fibre in Enterprise, Government and Carrier networks.

Omnitron iConverter media converter modules support a wide variety of protocols, data rates and cabling media types for flexible fibre connectivity in diverse network topologies. iConverter models support advanced switching capabilities and iConverter Fibre to Fibre NIDs feature integrated management and carrier grade fault detection capabilities.

iConverter media converter modules that support pluggable transceivers enable connectivity between copper network devices and fibre with a variety of distances and wavelengths. Pluggable transceivers that support CWDM wavelengths to enable connectivity to iConverter CWDM multiplexer modules.

Full Omnitron iConverter Copper to Fibre product pages

iConverter 10/100

iConverter 10/100Provide 10BASE-T or 100BASE-TX copper to 100BASE-FX fibre conversion. The iConverter 10/100 models support multimode and single-mode dual fibre with ST, SC and LC connectors; and single-mode single-fibre with SC connectors. The RJ-45 port supports 10/100 and Half/Full-Duplex auto-negotiation with both hardware and software manual override.

 

iConverter 10/100VT

iConverter 10/100VTThe iConverter 10/100VT supports the IEEE 802.1Q and 802.1p standards. It supports the 802.1Q VLAN packet tagging and untagging for segregating data in Enterprise networks, and enabling secure separation of Service Provider network management and customer data to improve security and intrusion protection.

 

iConverter 10/100M2

iConverter 10/100M2The iConverter 10/100M2 is a carrier-grade Network Interface Device (NID) that provides 10/100 copper to Fast Ethernet fibre media conversion with integrated management. For Service Providers, the 10/100M2 NID provides MEF 9, 14 and 21 certified demarcation of Carrier Ethernet E-Line services. The 10/100M2 is a cost-effective demarcation device for Service Providers to deliver best-effort Ethernet services.

 

iConverter 100FX/TX

iConverter 100FX/TXThe iConverter 100Fx/Tx models support multimode and single-mode dual fibre with ST, SC and LC connectors; and single-mode single-fibre with SC connectors. The RJ-45 port supports 100BASE-TX in either Half or Full-Duplex mode. A UTP crossover switch eliminates the need for a crossover cable and facilitates connectivity to network equipment such as hubs, switches and workstations.

 

iConverter 10FL/T

Omnitron 10FL/TThe iConverter 10FL/T models support multimode and singlemode dual fibre with ST, SC and LC connectors; and singlemode single-fibre with SC connectors. The RJ-45 port supports 10BASE-T in either Half or Full-Duplex mode. A UTP crossover switch eliminates the need for a crossover cable and facilitates connectivity to network equipment such as hubs, switches and workstations.

 

iConverter XG+

XGT+The iConverter XGT+ provides a variety of 10G data centre connectivity solutions, including resolving interface disparities between equipment with 10GBASE-T RJ-45 ports and existing rack servers or switches with fibre optic ports. Architecture changes such as migrating from Top of Rack to End of Row can present cabling challenges when extending network distances from racks of servers.

 

iConverter GX

The iConverter Gx modules are not supported in future software releases and are not recommended for new designs or deployments. View the iConverter Gx AN web page.

 

iConverter GXAN

iConverter GX ANThe iConverter Gx AN is a 1000BASE-T copper to 1000BASE-X fibre media converter, and is available as a compact unmanaged standalone unit or a managed chassis plug-in module. The RJ-45 port supports auto-negotiation or forced negotiation of duplex modes and pause capability. The fibre port supports both manual or auto-negotiation. The iConverter Gx AN features user-selectable link fault detection modes, including Link Propagate, Link Segment and Remote Fault Detection.

 

iConverter GX/T

iConverter GX/TThe GX/T models support multimode and single-mode dual fibre with ST, SC and LC connectors; and single-mode single fibre with SC connectors. The RJ-45 port supports 10/100/1000 and Half/Full-Duplex auto-negotiation with both hardware and software manual override controls.

 

iConverter GX/T2

iConverter GX/T2The iConverter GX/T2 is a 10/100/1000BASE-T copper to 100BASE-X or 1000BASE-X fibre media converter, and is available as a compact, unmanaged standalone unit or a managed chassis plug-in module. The iConverter GX/T2 supports jumbo frames up to 10,240 bytes.

 

iConverter GX/TM

The iConverter GX/TM modules are not supported in future software releases and are not recommended for new designs or deployments. View the iConverter GX/TM2 web page.

 

iConverter GX/TM2

iConverter GX/TM2For Service Providers, the GX/TM2 NID provides MEF 9, 14 and 21 certified demarcation of Carrier Ethernet E-Line services. The GX/TM2 is a cost-effective demarcation device for Service Providers to deliver best-effort Ethernet services. For Enterprise and Government and Utility networks, the GX/TM2 enables secure demarcation and management for mission-critical applications delivered over fibre infrastructure.

 

iConverter 2GXT

iConverter 2GXTThe 2GXT is a dual-channel media converter and four-port switch with two 10/100/1000BASE-T RJ-45 ports and two Small Form Pluggable (SFP) ports. The dual SFP fibre ports can be configured to provide 1:1 uplink protection with less than 50ms switchover when the 2GXT is deployed as a four-port switch.

 

iConverter 10GXT

iConverter 10GXTThe 10GXT is used to convert 10/100/1000 copper to Gigabit Ethernet fibre or 10 Gigabit Ethernet fibre. The 10GXT supports 1000BASE-X or 10GBASE-R Small Form Pluggable (SFP/SFP+) transceivers or 10GBASE-X XFP transceivers. SFP/SFP+/XFP transceivers enable adaptability to different fibre types and distances, and support Coarse Wave Division Multiplexing (CWDM) technology to increase the bandwidth capacity of fibre infrastructure.

 

FlexSwitch 2X4GT

Omnitron FlexSwitch 2X4GTThe FlexSwitch™ 2X4GT is a six-port Ethernet switch with four 10/100/1000 RJ-45 ports, one 10G (10GBASE-R) SFP+ or XFP fibre port, and one RJ-45 port that auto-negotiates to Gigabit or 10G (1000BASE-T/10GBASE-T). FlexSwitch 2X4GT models that support 10G SFP+ transceivers also support Gigabit transceivers for a seamless upgrade path from Gigabit to 10G. This compact unmanaged standalone unit offers rate-switching, and MAC learning for bridging Gigabit and 10 Gigabit Ethernet networks.

 

iConverter STM-1

iConverter STM-1The iConverter STM 1 copper to fibre media converter converts 155.52Mbps STM-1e coax to STM-1 fibre, and is available as a compact, unmanaged standalone unit or a managed chassis plug-in module. The iConverter STM1 can be used in Telecom or Enterprise applications where STM-1 or OC-3 transport is required beyond the maximum distance of copper (approximately 70m).

 

iConverter T1/E1

iConverter T1/E1The iConverter T1/E1 is a T1 (1.544Mbps) or E1 (2.048Mbps) copper to fibre media converter, and is available as a compact unmanaged standalone unit or a managed chassis plug-in module. The iConverter T1/E1 can be used to extend the demarcation point between service provider and networking equipment.

 

iConverter T3/E3

iConverter T3/E3The iConverter T3/E3 is a T3 (44.736Mbps) or E3 (34.368Mbps) coax to fibre converter, and is available as a compact unmanaged standalone unit or a managed chassis plug-in module. The iConverter T3/E3 can be used to connect to devices such as PBXs, multiplexers, routers and video servers via fibre.

 

iConverter X21

iConverter X21The iConverter X21 is a X.21 or RS-530 serial-to-fibre media converter, and is available as a compact, unmanaged standalone unit or a managed chassis plug-in module. The iConverter X21 supports several configuration modes to enable connections with a wide variety of X.21 and RS-530 devices.

 

iConverter RS-232

iConverter RS-232The iConverter RS232 is a managed serial RS-232 to fibre converter that transmits serial protocol over fibre media. The RS232 media converters operate in pairs, extending serial distances over fibre up to 120km, which improves noise immunity from electrical and magnetic interference.

 

iConverter RS-422/485

iConverter RS-422/485The iConverter RS422/485 is a managed serial RS-422 and RS-485 to fibre converter that transmits serial protocol over fibre media. The RS422/485 media converters operate in pairs, extending serial distances over fibre up to 120km, which improves noise immunity from electrical and magnetic interference.

 

 

Contact Protel Solutions about these products

Please enter your contact details below with a brief outline of how we may be able to support you. One of our Engineers with then contact you to discuss your requirement further.

Your Name (required)

Your Email (required)

Subject

Phone number

Website

Your Message

captcha

Phone: + 44 (0)1983 450018