iConverter NMM2 Network Management Module

NMM2The iConverter NMM2 provides comprehensive remote monitoring, configuration and alarm notification functions for all iConverter managed media converters and Network Interface Devices (NIDs). Installed in any slot of an iConverter chassis, the NMM2 manages all other modules and power supplies installed in the chassis through a high-speed management backplane. Additionally, all remote NIDs linked to the managed iConverter chassis can be managed by the installed NMM2 through a secure IP-less management channel.

Through the 10/100 RJ-45 Ethernet port, the NMM2 can be remotely accessed by IP-based management protocols, including SNMPv1/2c/3, TELNET and FTP. The serial console port provides local access and initial configuration from an RS-232 terminal. Management is accessed either via NetOutlook®, Omnitron’s SNMP Management Software, or by any third party SNMP management software. An intuitive Command Line Interface (CLI) can be accessed either via the serial port or TELNET.

The NMM2 provides real-time management, continuously collecting system status and module information. It reports the collected status to the network management applications and displays LED alarms for chassis power supplies. The NMM2 also provides comprehensive provisioning support for all local and remote iConverter modules, including port settings, VLANs and rate limiting. Network alarms are forwarded as traps to multiple trap hosts and recorded in a persistent system log.

In the event of a power outage, the NMM2 also supports dying gasp SNMP trap notification.

The NMM2 manages remote NIDs connected to the managed chassis via an IP-less management channel. Utilizing IEEE 802.3ah extensions, an NMM2 in a chassis at the network core can use a single IP address to manage up to 18 iConverter Network Interface Devices (NIDs) at different edge locations. This capability simplifies IP address management, improves network security and conserves the use of IP addresses.

Benefits Include

  • Supports SNMPv1, SNMPv2c, SNMPv3 and Telnet protocols
  • SNMP management via Omnitron’s NetOutlook® management software, or third-party SNMP management software
  • Password protected to prevent unauthorized access
  • Utilizes IEEE 802.3ah OAM extensions and Omnitron’s Secure OAM for IP-Less management
  • Management access available through the RJ-45 Ethernet port, serial port or from an adjacent module across the Ethernet backplane
  • 10/100Mbps RJ-45 port supports auto or manual negotiation and auto-crossover
  • Commercial (0 to 50°C), wide (-40 to 60°C) and extended (-40 to 75°C) temperature ranges
  • LED displays for immediate visual status of each port
  • Hot-swappable in 19-Module, 5-Module, or 2-Module chassis
  • Lifetime Warranty and free 24/7 Technical Support

Management

Active Controls

  • Link Propagate/Link Segment
  • Remote Fault Detection
  • Module Name
  • Chassis Name and Number
  • IP Address
  • 802.3ah OAM Enable
  • Secure IP-less OAM Enable
  • Subnet Mask
  • Gateway
  • Management Port Disable
  • Alarm Threshold Setting
  • Software updates via FTP
  • Telnet
  • Trap IPs
  • FTP Enable
  • Password Selection
  • Soft Switch Reload

Module Information

  • Module Type
  • Slot Occupied
  • Part Number
  • Serial Number
  • Configuration
  • Revision
  • Ports on Module
  • User-defined Identifier

Alarms / Traps

  • Warm Start
  • Link Up/Down
  • Chassis Insertion/Removal
  • Authentication Failure
  • Configuration Change
  • Temperature Out-of-Range
  • Power Supply Out-of-Range
  • Power Supply Insertion/Removal
  • Module Reset
  • Port Link State Change
  • FTP Session Open/Close
  • Telnet
  • Session Open/Close
  • Dying Gasp (Power Loss Trap)

Chassis Status

  • Power Status
  • Power Output Voltage
  • Chassis Temperature

Module Status

  • Module Power
  • Link Status
  • Diagnostic Status
  • Management

Application Example

In this application example, iConverter 10/100M2 plug-in modules are installed in the 19-Module chassis, and connected via the fibre link to a standalone 10/100M2 Network Interface Device (NID). With an NNM2 installed in the 19-Module chassis, an IP-less management channel between the 10/100M2 link partners is established. The IP address resides only at the network core (NMM2), and does not exist on the customer network.

NMM2 Application Example

Protel Solutions.co.uk - Download the Datasheet

 

 

 

Please enter your contact details below with a brief outline of how we may be able to support you. One of our Engineers with then contact you to discuss your requirement further.

Your Name (required)

Your Email (required)

Subject

Phone number

Website

Your Message

captcha

Phone: + 44 (0)1983 450018